Washing

How to Strip Cloth Diapers With RLR

When cloth diapers need stripping, how to use RLR in a tub soak or the washer, how stripping differs from bleaching, and how to stop buildup coming back.

On this page
  1. What RLR is (and what stripping means)
  2. Stripping vs bleaching: which do you need?
  3. Signs your diapers may need stripping
  4. Before you strip: rule out the routine
  5. How to strip cloth diapers with RLR in a tub
  6. How to use RLR in the washing machine
  7. Covers, PUL and all-in-ones
  8. What about the murky water?
  9. How often should you strip?
  10. After stripping: preventing buildup

What RLR is (and what stripping means)

RLR is a laundry treatment powder sold in single-use packets. Cloth diaper parents use it to strip diapers, meaning to remove mineral deposits and residue that have built up in the fabric over many washes.

Buildup usually comes from hard water. Calcium and magnesium can bind with detergent and soil and settle in the fibers. Over time this can leave inserts stiff, dingy, less absorbent and smelly, even right after washing.

RLR is a treatment for clean diapers. It’s not a detergent, and it doesn’t replace your regular wash.

Stripping vs bleaching: which do you need?

People often use these terms interchangeably, but they do different things:

Stripping (e.g. RLR) Bleaching
Main purpose Remove mineral and residue buildup Kill bacteria, yeast and other microbes
Typical trigger Hard water, stiffness, stink that returns right after washing Yeast rash, secondhand diapers, illness, persistent stink
Disinfects? No Yes, when used correctly

If your diapers need both, do them as separate steps with a full wash in between. Never combine RLR and bleach in the same soak. Mixing cleaning chemicals can be unsafe, and each works best on its own. For the sanitizing side, see how to bleach cloth diapers safely.

Signs your diapers may need stripping

  • Inserts feel stiff, crunchy or rough even after a dryer cycle.
  • Diapers smell clean out of the wash but smell strongly of ammonia or “barnyard” soon after they get wet.
  • Absorbent fabrics start to repel liquid or leak, and fit isn’t the cause.
  • You live in a hard water area and haven’t been using a water softening additive.
  • You bought secondhand diapers with an unknown wash history (often stripped and bleached).

Before you strip: rule out the routine

Stripping removes buildup. It doesn’t fix the routine that caused it. If your detergent dose is low, your drum is half-empty, or your main wash is a short cycle, the stink will come back within weeks.

Before reaching for RLR, check your routine against our complete cloth diaper wash routine, and test your water hardness if you haven’t. Our hard water washing guide explains how.

Also look at what goes on your baby. Non-cloth-safe diaper creams can cause repelling, and stripping may not fully remove them.

How to strip cloth diapers with RLR in a tub

This is a general outline. Follow the instructions on your RLR packet, since directions and amounts are printed there and may change.

  1. Start with clean diapers. Run them through your normal wash routine first. Stripping dirty diapers just moves soil around. They can be wet or dry.
  2. Fill a clean bathtub or large basin with hot water. Use the hottest tap water your diapers’ care labels allow.
  3. Dissolve the RLR in the water according to the packet directions. The packet will say how much to use for the size of the batch.
  4. Add the diapers and push them under so everything is submerged.
  5. Soak for several hours, stirring now and then. Many people leave diapers for a few hours, until the water has cooled. Check your packet for its recommended time.
  6. Drain and wring the diapers. Be careful lifting them, since soaked inserts are heavy.
  7. Run a rinse or wash cycle with no detergent, or follow the packet’s instructions, to flush out the RLR.
  8. Dry as usual.

Safety: keep children and pets away from the tub while diapers are soaking. Any amount of standing water is a drowning risk for young children. Wear gloves if your skin is sensitive, and keep the powder out of reach.

How to use RLR in the washing machine

If you can’t soak in a tub, you can usually use RLR in a washer:

  • Load clean diapers.
  • Add the RLR as directed and run a hot, long cycle with no other detergent unless the packet says otherwise.
  • Run an extra rinse or two afterwards.

A top loader that you can pause partway through to let the diapers soak gives results closer to a tub soak. HE front loaders use less water, so a tub soak may be more thorough.

Covers, PUL and all-in-ones

Hot soaks are harder on waterproof laminate (PUL/TPU) and elastic than on plain cotton or hemp. Some manufacturers advise against soaking covers, or against stripping at all, and doing it anyway could affect a warranty claim.

To be cautious:

  • Strip inserts, prefolds and flats (absorbent pieces only) where possible. These are where mineral buildup usually causes problems.
  • For pockets and all-in-ones, check the brand’s care instructions first. If in doubt, ask the manufacturer.
  • Don’t strip wool covers. Wool needs gentle, wool-specific care.

What about the murky water?

Many people post photos of brown or cloudy soak water as proof their diapers were “dirty.” Some of that color can come from minerals and residue, and some from dyes released by colored fabrics. Murky water doesn’t by itself tell you the diapers were unclean, and clear water doesn’t mean they’re perfect. Judge the results by how the diapers feel, smell and absorb in use.

How often should you strip?

Only when you need to. Stripping is a reset, not a maintenance step. Frequent hot soaks add wear, especially to elastics and waterproof layers.

If you find yourself needing to strip regularly, the routine needs changing. The usual fixes are more detergent, a water softening additive in hard water, a fuller drum, and a longer main wash.

After stripping: preventing buildup

  • Soften hard water at every wash. Use a powder detergent formulated for hard water, a softening additive, or both.
  • Use enough detergent. Too little leaves soil and minerals behind.
  • Load the machine properly so diapers rub against each other.
  • Wash every two to three days so soiling doesn’t sit and set.
  • Keep diaper creams away from fabric unless they’re cloth-safe, or use a liner.

If the smell after stripping is sharp ammonia rather than a dull mustiness, our article on why cloth diapers smell like ammonia goes through the other causes to rule out.

The complete guide to washing

How to Wash Cloth Diapers: A Complete Wash Routine
Read the guide

Keep exploring

Guides from other topics

All topics →