A cover, sometimes called a shell or wrap, is the waterproof outer layer of a cloth diaper. If you use flats, prefolds or fitted diapers, the cover is a separate piece. With AI2 systems, the shell is the base that inserts snap into. With pockets and all-in-ones, the same waterproof material is built in. Understanding covers, and the PUL fabric most of them are made from, helps you buy the right ones and keep them working.
What a Diaper Cover or Shell Does
A cover’s job is to hold moisture in. It doesn’t absorb. A good cover:
- Seals at the legs and waist without leaving red marks that linger
- Is large enough to fully contain whatever absorbent layer is under it
- Lets some water vapor out, so it doesn’t feel like a plastic bag
- Can be wiped clean and reused between changes when it isn’t soiled
What PUL Is
PUL stands for polyurethane laminate. It’s a fabric, usually polyester knit, with a thin polyurethane film bonded to one side. The fabric gives it strength and a soft outer surface. The film makes it waterproof. Because the film is thin, PUL lets a small amount of water vapor through. That’s why it’s often described as “breathable,” though it is much less breathable than wool or fleece.
PUL is used in covers, AI2 shells, pocket diapers, all-in-ones, wet bags and swim diapers.
PUL vs TPU
TPU (thermoplastic polyurethane) is a type of polyurethane film that can be bonded to fabric with heat rather than chemical adhesives or solvents. In everyday cloth diaper talk the two terms are used loosely. Many products labeled “TPU” are polyester fabric laminated with a TPU film, which is effectively a kind of PUL. Some brands highlight TPU because of the heat-bonding process. In practice, both work well when made well. Lamination quality matters more to the user than the label.
Types of Covers
Wrap-Style Covers
The classic cover for flats, prefolds and fitteds. It’s a shaped piece of PUL with elastic legs and back, closing with snaps or hook and loop. Many have leg gussets, an inner elastic ruffle that adds a second barrier. Wrap covers come in sized and one-size versions.
AI2 Shells With Snap-In Inserts
These are covers with a wipeable PUL interior and snaps inside to hold an insert in place. They can also go over a trifolded prefold or flat. Our AI2 and snap-in insert guide explains these systems, including Best Bottom and Buttons.
Pull-On Covers
These have no closures and pull on like underwear. They’re common for toddlers and potty learning, and some newborn-size covers use this style too.
Non-PUL Options: Wool and Fleece
Wool and fleece covers are breathable, have no plastic film, and are popular at night. Wool needs hand washing and lanolizing. Fleece is cheap and easy to sew. See wool diaper covers and fleece diaper covers.
Features That Matter
- Leg gussets: Single or double gussets help contain runny poop and help on slim legs.
- Rise settings: One-size covers use rows of snaps to shorten the diaper. Learn how in adjusting rise snaps.
- Closures: Snaps last longer. Hook and loop is quicker and adjusts more finely. See snaps vs hook and loop.
- Wipeable interior: Covers with PUL exposed on the inside can be wiped out. Covers with fabric-bound edges can wick.
- Back elastic and rise height: A taller back with good elastic helps prevent blowouts up the back.
- Sized vs one-size: Sized covers often fit newborns and big toddlers better. One-size covers last longer. See one-size vs sized.
How Many Covers You Need, and Reusing Them
With flats, prefolds or AI2 inserts, a common rule of thumb is one cover for every two or three changes, as long as the cover isn’t soiled. Between changes, wipe the inside (or let it air dry if just damp) and put in a fresh absorbent layer. A cover with poop on it should go into the wash. Many families find that four to eight covers are enough for full-time use with washing every two to three days. Newborns, who poop often, may need more. Fitted diapers often go through covers a little faster, since a damp fitted can make the cover damp too.
Caring for PUL So It Lasts
PUL is durable but not indestructible. To help it last:
- Follow the manufacturer’s wash instructions. Most say warm or hot washing is fine.
- Avoid very high dryer heat for long periods, which can contribute to delamination over time. Many brands suggest low heat or line drying.
- Skip fabric softener, which can coat fabrics and affect performance.
- Fasten laundry tabs on hook and loop covers before washing.
- Avoid stretching PUL hard when it’s hot from the dryer.
Why Covers Leak
When a cover leaks, check these in order:
- Fit: Gaps at the legs or a rise set too long or short. Leg elastic should sit in the leg crease.
- Absorbent layer sticking out: Any fabric poking past the cover edge will wick moisture onto clothes.
- Absorbent layer is saturated: The cover holds water in but can’t add absorbency. If the prefold or insert is soaked through, you need more absorbency or more frequent changes.
- Compression: Tight clothing or car seat straps can squeeze moisture out of an overfull insert.
- Damage: Hold the cover up to light and look for cracks, peeling or tiny holes in the laminate. Delaminated covers usually need to be replaced.
Safety and “Least Toxic” Questions
Parents often ask which diaper brand is “least toxic.” There isn’t a reliable single answer, and it’s wise to be cautious of marketing claims. Some ways to make an informed choice:
- Look for independent textile certifications such as OEKO-TEX Standard 100, which tests for a range of harmful substances, or GOTS for organic fibers in absorbent layers.
- In the US, cloth diapers sold as children’s products should meet federal children’s product safety requirements. Reputable sellers can usually tell you about testing.
- If you want to minimize synthetic materials touching skin, use natural-fiber absorbency (cotton, hemp, wool) under the cover, or choose wool covers.
Where to Buy PUL Fabric
If you sew your own covers, PUL is sold by the yard at many online fabric shops, some cloth diaper supply stores, and some larger craft and fabric stores. You’ll see it sold by thickness (often 1 mil or 2 mil), with 1 mil common for diapers and 2 mil for heavier items like changing pads. Look for PUL described as suitable for diapers. Test a scrap for stretch and waterproofing before cutting into a full piece.
For how covers fit into the bigger picture of cloth diaper types, see cloth diaper systems explained. If you use covers with prefolds, our flats and prefolds guide explains folds that sit neatly inside them.