Why New Inserts Need Prepping
New natural-fiber inserts, including cotton, bamboo and especially hemp, contain natural oils and waxes, and sometimes manufacturing finishes. Until these wash out, the fabric absorbs poorly. Washing also opens up and “fluffs” the fibers, and the fabric usually shrinks and thickens a little, which increases absorbency further.
That’s why brand-new natural inserts often leak in their first few uses. They aren’t faulty, they just aren’t fully prepped. Synthetic inserts such as microfiber don’t have these oils, so they need far less prep.
Always check the manufacturer’s instructions first. They know their fabrics, and following them may matter for warranties.
How Many Washes Each Material Needs
These are typical ranges. Absorbency usually keeps improving for a while after you start using the inserts.
| Material | Typical prep | Notes |
|---|---|---|
| Microfiber | About 1 wash | Mainly to clean it before use |
| Stay-dry (microfleece, suedecloth) | About 1 wash | Synthetic; no natural oils to remove |
| Cotton (prefolds, flats, inserts) | Several washes, often about 3–5 | Prefolds shrink and “quilt up” |
| Bamboo | Several washes, often about 3–5 | Usually prepped like cotton |
| Hemp and hemp-cotton | The most, often 5 or more | Can take many more washes to reach full absorbency |
| Blends (bamboo-hemp, etc.) | Follow the slowest fiber | Hemp blends behave like hemp |
Many manufacturers say you can start using natural inserts after a wash or two, as long as you change more often until they reach full absorbency.
How to Prep Hemp Inserts, Step by Step
Hemp takes the most work, so here’s a full routine. The same steps work for cotton and bamboo, just with fewer washes.
- Read the label. Note any temperature or drying limits.
- Wash separately from synthetics at first. Many cloth diaper guides suggest prepping natural fibers apart from microfiber, stay-dry fabrics and diaper shells, so the natural oils don’t transfer and reduce the synthetics’ absorbency. Some manufacturers say washing together is fine. If in doubt, keep them apart for the first wash or two.
- Use a hot or warm wash with a normal amount of detergent. Stay within the label’s limits. You don’t need extra detergent, which can leave residue.
- Repeat. Many parents run several washes back to back. Some manufacturers recommend drying between washes, as the shrink-and-expand cycle helps. Others don’t require it. Follow your label.
- Dry. Tumble drying usually leaves hemp softer than line drying. Expect some shrinkage, particularly in the first few cycles.
- Test absorbency. Drip or pour a little water onto the insert. If it beads up or runs off, keep washing. If it soaks in readily, it’s ready to start using.
- Start using, and change a little more often at first. Hemp’s absorbency typically continues to increase over the next several washes.
Can You Speed Up Hemp Prep?
A few things help:
- Longer, hot cycles (within the label’s limits) seem to work faster than short, cool ones.
- Washing with other natural-fiber items such as cotton prefolds or towels adds agitation and gets more done per load.
- Start using the inserts early with more frequent changes, since normal washing continues the prep.
Some parents boil natural-fiber inserts to speed things up. We’d only consider that for plain natural-fiber inserts with no waterproof layer, elastic, snaps or synthetic topper, and only if the manufacturer allows it. Boiling can damage some fabrics, and handling boiling water carries a burn risk. Long hot wash cycles do the same job more gently.
Prepping Cotton Prefolds, Flats and Inserts
Cotton prefolds usually shrink and become thicker and more “quilted” in their first several hot washes and dries. That’s normal and improves absorbency. Flats, being single-layer, usually need fewer washes than prefolds. Expect some shrinkage, so allow for it when choosing sizes.
Prepping Bamboo Inserts
Bamboo (viscose) inserts are usually prepped like cotton. Wash them several times and check the label for heat and drying limits, as some bamboo fabrics hold up better with lower heat. For more on how bamboo and hemp differ, see bamboo vs hemp cloth diaper inserts.
Prepping Microfiber and Stay-Dry Inserts
Microfiber and stay-dry inserts usually need only one wash before use. They’re synthetic, so there are no natural oils to remove. Avoid fabric softener and dryer sheets, which can coat the fibers and cause repelling. Our cotton vs microfiber comparison covers microfiber care in more detail.
Prepping Secondhand Inserts
Used inserts don’t need prepping for absorbency, but you’ll want them thoroughly clean before use. Run them through your normal diaper wash routine. Many cloth diaper care guides also suggest a sanitizing wash or diluted bleach soak for secondhand diapers. If you do this, follow the manufacturer’s guidance and a reputable diaper-care source for the dilution, never mix bleach with other cleaning products, and rinse thoroughly afterward.
If secondhand inserts repel water after washing, they may have build-up from detergent or fabric softener and might need a deeper cleaning (“stripping”).
Prep Mistakes to Avoid
- Giving up after one leaky use. New natural inserts often need more washes.
- Using fabric softener or dryer sheets, which reduce absorbency.
- Using far too much detergent, which can leave residue.
- Prepping hemp with your diaper shells and microfiber when the manufacturer advises keeping them apart.
- Ignoring shrinkage. Prefolds and hemp inserts may end up smaller than you expect.
Once your inserts are prepped, our guide to layering cloth diaper inserts helps you stack them for the best absorbency. If you’re still choosing materials, start with our overview of cloth diaper insert types.