Cloth Diapering Basics

Does pee go through cloth diapers?

A properly fitted cloth diaper with a waterproof layer holds pee in. Learn how cloth diapers stop urine, why leaks happen, and how to fix them.

On this page
  1. The Short Answer
  2. How a Cloth Diaper Stops Pee
  3. When Pee Does Get Through
  4. Quick Leak Troubleshooting Table
  5. How Often Should You Change a Cloth Diaper?
  6. Will My Baby Feel Wet?

The Short Answer

A well-fitted cloth diaper shouldn’t let pee through to your baby’s clothes. The inner fabric soaks up the urine, and a waterproof layer on the outside keeps it in. Pee gets through when something isn’t right: there’s no cover, the diaper is full, fabric is poking out of the cover, the fit is off, or the diaper has stopped absorbing properly. Most of these are fixable, and our guide to why cloth diapers leak goes into more depth.

How a Cloth Diaper Stops Pee

Every working cloth diaper setup has two jobs to do:

  1. Absorb. Cotton, bamboo, hemp, or microfiber soak up urine and hold it.
  2. Contain. A waterproof layer stops the moisture reaching clothes and bedding. This is usually polyester laminated with PUL or TPU, or a wool or fleece cover.

In an all-in-one or pocket diaper, both jobs are handled by one piece. In a two-part system, a flat, prefold, or fitted does the absorbing and a separate cover does the containing.

Some diapers have a “stay-dry” lining of fleece or suedecloth next to the skin. In this case pee is meant to pass through the top layer into the absorbent fabric underneath, so the surface against your baby feels drier. The waterproof outer layer is what stops it from going any further.

When Pee Does Get Through

No cover on a two-part diaper

Flats, prefolds, fitteds, and contours aren’t waterproof on their own. Without a cover, pee will soak through to clothing. That’s expected. Some families let babies go without a cover for short periods at home to give their skin some air, but for everyday use you need one.

The diaper is full

Cloth diapers don’t contain the super-absorbent gel found in disposables, so they hold less and fill up faster. If the whole absorbent area is soaked at a change, the diaper simply ran out of capacity. You can change it sooner or add more absorbency, such as a booster or a hemp insert.

Fabric poking out (wicking)

If any absorbent fabric sticks out past the leg or waist edges of the cover, moisture travels along it onto clothing. This is called wicking. After every change, run a finger around the leg and waist openings and tuck everything inside.

Poor fit at the legs or waist

The leg elastic should sit in the crease where the leg meets the body, about where underwear would sit, not lower down on the thigh. Gaps at the legs or a loose waist leave a path for leaks. With one-size diapers, check that the rise setting suits your baby right now.

Compression

Tight clothing, car seat straps, or a carrier can squeeze liquid out of an insert, especially microfiber, which holds liquid loosely. You’ll often see damp spots along the waistband or legs even though the diaper isn’t soaked. Looser bottoms and natural-fiber inserts can help. See our guide to clothes that fit over cloth diapers.

Repelling

If pee beads up or runs off the diaper instead of soaking in, the fabric may be coated or clogged (see why cloth diapers repel). Common causes:

  • new natural-fiber diapers that haven’t been prepped enough
  • buildup from some rash creams, fabric softener, or dryer sheets
  • mineral deposits from hard water

Our guide to properly caring for cloth diapers covers prepping and wash routines. For creams, see rash creams that are safe for cloth diapers.

Worn-out waterproofing

PUL and TPU eventually wear out. Look for peeling, cracking, or tiny holes, and hold the cover up to the light to check. A cover that leaks everywhere at once, even with a fresh insert, may need replacing. Wool covers lose water resistance as their lanolin wears off and need relanolizing from time to time.

Absorbency in the wrong place

Babies wet in different spots. Many boys wet more toward the front, and many girls more toward the middle. If leaks happen in one area, try folding inserts so the extra layers sit where your baby actually wets.

Quick Leak Troubleshooting Table

What you see Likely cause Try
Whole diaper soaked at change Not enough absorbency or too long between changes Change sooner or add a booster
Damp line at leg or waist only Wicking or fit Tuck fabric in; adjust leg fit
Wet spots under straps or tight pants Compression Looser clothes; natural-fiber inserts
Pee beads on the surface Repelling Prep more; check creams and wash routine
Leaks right after a pee, diaper mostly dry Absorbency in wrong spot or fabric absorbs slowly Move layers; use a fast-absorbing layer on top
Cover damp all over Worn waterproof layer Inspect and replace the cover

How Often Should You Change a Cloth Diaper?

During the day, most families change cloth diapers about every two to three hours, and right away after a poop. Newborns often need changing more often.

You don’t have to change after every single pee, but don’t leave a wet diaper on for long stretches. Lingering moisture can irritate skin. Overnight diapers are the main exception, because they’re built with extra absorbency to last longer. If your baby gets red or sore, change more often and check in with your pediatrician if it doesn’t clear up.

Will My Baby Feel Wet?

In natural-fiber diapers without a stay-dry layer, your baby will usually feel some dampness. This doesn’t harm healthy skin if you change regularly. If your baby seems uncomfortable, or their skin reacts to wetness, a fleece or suedecloth stay-dry liner can make the surface feel drier.

For more on choosing and fitting diapers, see our beginner’s guide to cloth diapering basics.

The complete guide to cloth diapering basics

Cloth Diapering Basics: A Beginner's Guide to Using Cloth Diapers
Read the guide

Keep exploring

Guides from other topics

All topics →